I’m working on setting up my first homelab. I have an older dell optiplex with a duel PCIe NIC in it. I was wondering if I could setup OPNsense as a docker container or virtual machine so that I could also use the extra resources of the box for other things besides just being a router. Is this a good idea?

  • kroy@lemmy.worldEnglish
    13·
    1 year ago

    Passing through a NIC just adds complexity, not lessens it. And is a bad idea for a plethora or reasons

    • Solar Bear@slrpnk.netEnglish
      1·
      1 year ago

      Having tried both, I found it far easier and less troublesome to just add a PCI passthrough than it is to worry about managing the network both on the host and in the VM. As long as FreeBSD supports the driver, I strongly recommend passthrough vs virtualized NICs.

    • corroded@lemmy.worldEnglish
      2·
      1 year ago

      I would strongly disagree. In terms of setting up OPNSense (I use pfSense, but same concept), it’s easier to just do a PCI passthrough. The alternative is to create a virtual network adapter on your hypervisor, bridge it to a physical NIC, and bind the virtual adapter to the VM. The only advantage to be gained from that is being able to switch between physical NICs without reconfiguring the OPNSense installation. For someone with a homelab, when would you ever need to do that?

      My Proxmox server uses a 10Gb PCIe adapter for its primary network interface. The onboard NICs are all passed through to pfSense; I’ve never had any need to change that, and it’s been that way for years.

      I don’t mean this to sound overly critical, and I’m happy to be proven wrong. I just don’t see a “plethora of reasons” why doing PCI passthrough on a NIC is a bad idea.

      • kroy@lemmy.worldEnglish
        2·
        1 year ago

        I’m happy to discuss it, as I’ve written articles about it.

        I live high level routing and firewalling in VMs (60 Gbps+), and there are a couple of realities you need to accept, especially when you involved a *BSD in the mix.

        1. *BSD’s networking drivers and, to a lesser degree, the whole stack SUUUCK. This becomes extra poignant when you involve *pf, which is incredible for hand editing, but also horrible for performance because it’s a straight top-to-bottom list.
        2. We could argue about the whole networking stack sucking all day, but in reality, it’s the driver situtation that really brings it down. That’s why “You must buy Intel” is such a mantra on *BSD. Because they are about the only drivers which don’t make for a completely horrible experience. You can meme about how terrible Realtek is, but really it’s only terrible on *BSD. It’s a first-class linux citizen, and often supports better hardware features than the ancient X520, pre-Connect-4, etc people circle-jerk about. And if you often losing out on cool new features/offloads/abilities.
        3. The virtio drivers are usually more efficient and performant than most physical hardware drivers (on *BSD)
        4. You asked “why would anyone ever need to do that?”. It’s simple. High availability. You can run two router/firewall VMs on two different hosts and have zero downtime. Or, if you only want one, you can migrate the VM either manually or automagically, and only suffer the downtime for a reboot as the VM moves to a different host. You can share the same physical NIC between multiple VMs with SR-IOV for maximum low-latency networking, aka storage. It’s a waste throwing 10Gb at just pfSense when it’ll be idle most of the time, and with older hardware pfSense isn’t going to even be able to hit half of that.
        5. Your VM just works if you ever have to move it to another host. Your main routing and firewall VM is now tied to a single specific host. In a disaster recovery situation, this is going to make you hate yourself as you basically end up needing to either physically pull a card and re-setup passthrough, or setup passthrough on a new card, make sure the VM is bound to those MACs. When it’s fully virtualized, it’s hardware agnostic. Your VM may think it’s 10Gb on a single link, but underneath the links are high availability (aka vSphere vDS), on different VLANs, etc. My example here is a few years ago where I swapped in a Z8350 WYSE 3040 when my main router died with 40Gb uplinks. Sure, I was limping for a few days, but as far as my router is concerned, there is no difference.
        6. NUMA becomes an issue. Even single processors have NUMA nodes now, and it wouldn’t be difficult for someone not knowing was a NUMA node is to create a NUMA issue, where you incur huge penalties going from CPU/Chipset to RAM to NIC and back again, depending on where the items are physically arranged in the system. This is doubly poignant in the *BSD world.
        7. If a 1Gb interface is your bottleneck, your network design is broken. There is no reason for most people in a homelab to try and route >1Gbps on your edge. Don’t packet inspect it, and internally you are up to 10Gbps and beyond. Sure, a >1Gbps link might be a reason in 2023, but what’s your 95th percentile, like 25Mbps if you are lucky. It’s only “hawt” for your speedtest numbers, and an occasional download. And you can do 10Gbps pretty easily with virtio on basically any semi-modern system especially with the large files that most people would want 10Gb for, and not dedicate a PCIe slot to it and make it portable.

        I mean, you do you. But I’d much rather to just be able to change the uplink on a vSwitch or bridge to get my router going again instead of having to reboot, passthrough, insert grub cli options, swap cards, etc.