It’s on everything, my fingernails are glued to my skin underneath, I hate everything and most of all I hate spray foam.

Thanks for letting me rant. I normally read instructions before using a product and now I’m avoiding the room where it’s on everything… How fucked am I?

Update: We’ve cleaned most of it up from the room… Our hands, not so much lol. I appreciate the advice and support, hopefully y’all got a good laugh on our behalf :)

Ps. It works great as a diy wax for hairy arms!

  • m__a__b@lemmy.ca
    link
    fedilink
    arrow-up
    23
    ·
    8 months ago

    It’s a very fine line between “I don’t think that’s enough” and “OMG, will it ever stop?”

  • TropicalDingdong@lemmy.world
    link
    fedilink
    arrow-up
    34
    arrow-down
    1
    ·
    8 months ago

    Ha ha ha… I knew before I clicked it what you were going to say.

    That shit is like… nasty af. Also, another good reason to bite the bullet and do what the quality tradespeople do:

    Buy a box of nitrile gloves and store them whereever you keep your solvents/ sprays/ paints/ anything…

    • Death_Equity@lemmy.world
      link
      fedilink
      arrow-up
      15
      arrow-down
      3
      ·
      8 months ago

      Nitrile goes on the moment anything sticky comes out. Spending the next hours or days picking bits of bullshit off your dick ticklers isn’t great.

      I honestly wear gloves when working all the time, work gloves or nitrile, because I don’t want rough hands with tiny cuts you only find when you use sanitizer.

      I understood why he wore a glove with Vaseline in them, you wife probably does too.

  • over_clox@lemmy.world
    link
    fedilink
    arrow-up
    5
    ·
    8 months ago

    Oof, I feel your frustration.

    As long as you didn’t snort it, you’ll be fine in the long run… 😂

  • Onno (VK6FLAB)@lemmy.radio
    link
    fedilink
    arrow-up
    13
    ·
    edit-2
    8 months ago

    Life is the collection of things you learnt. If you still have all your fingers and toes, this was a cheap lesson to learn :)

      • ashok36@lemmy.world
        link
        fedilink
        arrow-up
        3
        arrow-down
        1
        ·
        8 months ago

        The foam gets on the gloves and then you take them off. Et Voila, no foam on your hands.

          • mantra@lemmy.zip
            link
            fedilink
            arrow-up
            1
            ·
            8 months ago

            Nitrile gloves have been shown to offer a bit more protection against isocyanates than latex. If you’re just worried about mess and aren’t allergic, then probably doesn’t matter.

      • baldingpudenda@lemmy.world
        link
        fedilink
        arrow-up
        4
        ·
        8 months ago

        Latex free became common as some ppl have latex allergies. If you’re not allergic it’s not an issue, but I haven’t seen latex gloves in a while.

  • pdavis@lemmy.world
    link
    fedilink
    arrow-up
    1
    ·
    8 months ago

    I put on an old pair of coveralls, gloves, hat, hood, respirator, old shoes, goggles. I covered the doorway to the room with plastic and setup a fan for ventilation and pre-heated the bottles. Even with all that I was miserable. I was hot and sweaty, had trouble breathing, and couldn’t see out of the goggles. My arms were tired and the foam mixture wasn’t always mixing properly and ended up wasting a lot of the mixture. It was still pretty expensive and time consuming… not sure I would do it again.

  • seathru@lemmy.sdf.org
    link
    fedilink
    English
    arrow-up
    13
    ·
    edit-2
    8 months ago

    It’ll eventually wear off your skin. In a few days. On other, relatively non porous surfaces, it can be removed easily once cured. Porous surfaces like wood, cloth, or carpet? Sorry, it’s here to stay.

        • PrincessTardigrade@lemmy.worldOP
          link
          fedilink
          arrow-up
          2
          ·
          8 months ago

          This is excellent advice actually! My first instinct after getting it on my skin was to wash it off with soap and water, and learned afterwards that water causes it to cure faster. So it would make sense to dampen the wood to get it to stick better

  • dmtalon@infosec.pub
    link
    fedilink
    arrow-up
    8
    ·
    8 months ago

    Probably too late for now but if you ever have a big spray foam job in the future :)

    Best thing I found for spray foam is the reusable sprayer that you screw larger cans on.

    It’s soooo much better. I was sealing up everything I could in the basement before drywall went up.

    We had a radon mitigation system installed after discovering ours was quite high. The guy that came had one of these guns to seal up all the cracks in the floor

    Great stuff Pro 14. It’s $60 bux but is a game changer. You can store the connected can on it for 30 days it says. They have a spray can of cleaner to clean it after your done.

    https://www.homedepot.com/p/GREAT-STUFF-PRO-Pro-14-Insulating-Spray-Foam-Dispensing-Gun-99046685/300841046

    • Omacitin@lemmy.world
      link
      fedilink
      arrow-up
      1
      ·
      8 months ago

      Can confirm, the metal spray guns are way better than the disposable cans. Their ‘reusable’ disposable cans had poor flow and kept clogging on me.

  • Yer Ma@lemm.ee
    link
    fedilink
    arrow-up
    11
    ·
    8 months ago

    Keep putting oils on your skin, it will help, I’ve been there, lo siento